|
|
|
Tel 07789391865
|
Static Cling Film for Glass, Plastic & Polycarbonate/Perspex IT'S REMOVABLE & REUSABLE It adheres to smooth glass, plastic, polycarbonate/perspex through the use of static electricity, without glue or adhesives. It clings as easily to a concave shape as it does to a smooth flat surface Eliminates Over 57% Of The Sun's Heat Rejects 97.6% Of Sun's U/V Rays (which damages your skin & fades upholstery) Gives Privacy & Extra Security It clings as easily to a concave shape (rear windscreens - in one piece & without heat shrinking) as it does to a smooth flat surface. Solar Stat is ideal for all cars, motorhomes, caravans, boats, sunroofs and much, much more. PROTECT YOUR PETS WHILST TRAVELLING IN YOUR VEHICLE Solar Stat offers the consumer a product which adheres through the use of static electricity to any smooth glass or plastic surface. All Solar Stat® sun control products are durable, easy to apply & remove, and are reusable. The durability and ease of application, provides products that can be purchased and installed at a fraction of the cost when compared to the professional installation of conventional film. Internal fitting only on vehicles Tinted films should not be applied to drivers or front passenger window Automotive window film can dramatically improve your passenger comfort by significantly reducing heat and glare, besides protecting them from harmful UV light- by up to 98%. In the summer months, your vehicles fuel consumption will improve as there will be less reliance on air-conditioning system. By reducing the suns harmful effects, your cars interior will stay looking good for longer- helping to keep its value higher. Darker tints will stop prying eyes, giving your passengers privacy and helping to hide personal belongings and shopping stored in your vehicle Installation is as easy as 1- 2 - 3 - - - - Watch the video Unlike adhesive films, there is no front or back to Solar Stat. Once properly applied and trimmed, Solar Stat will stay in place until you decide otherwise. DETAILED
WINDOW TINTING INSTALLATION INSTRUCTIONS 1.
Measure: Measure glass and cut the film 12mm larger than actual surface. 2.
Spray: Spray glass and the Solarstat “EazyTint” film thoroughly with
a glass cleaner before applying Solarstat “EazyTint”. 3.
Apply: Starting at the top, apply Solarstat “EazyTint”to the window.
There is no front or back to the film so either side can be applied to the
glass. Position and smooth out most wrinkles and large bubbles until the film
overlaps the frame. If the film begins to cling to itself apply additional
window cleaner. 4.
Squeegee: Spray the surface of the film with window cleaner and squeegee
out the excess air and moisture from between the film and the glass. 5.
Trim: Allow approx. 20-30 minutes of drying time before trimming. Use a
straight edge ruler to press Solarstat “EazyTint” to the inside edge of the
window frame. Leave approximately 1mm of glass exposed around the perimeter of
the window to allow the film to properly adhere to the surface of the glass. 6.
Touch Up: Spray the surface of the film again and squeegee the edges
firmly against the glass. Any excess moisture should evaporate within a few
days. During the first 10 hours after installation Solarstat “EazyTint”
should not be disturbed. VEHICLE
WINDOW TINTING INSTALLATION ENSURE
YOU CHECK WITH YOUR LOCAL AUTHORITIES FOR RESTRICTIONS REGARDING THE USE OF
WINDOW TINT ON AUTOMOBILES. THERE ARE PENALTIES FOR FAILING TO COMPLY WITH
WINDOW TINTING REGULATIONS. NOTE: Do
not allow the film to contact the “black dot matrix” of any window as the
film must only contact the glass. Follow
Steps 1-5 in the Application Instructions. When aligning and trimming, Solarstat
“EazyTint” for vehicle application, it is recommended to first work on the
outside of the vehicle’s windows. This allows for easier access to windows
during trimming. For roll-up windows, leave an extra 10-15mm along the bottom
edge. This will be necessary later to prevent the film from being peeled back
during window operation. After
final trimming to size, remove the film from the outside and apply to the inside
of the vehicle, repeating Steps 3 and 4. Using a credit card or butter knife,
slide the 10-15mm excess below the bottom rubber gasket before aligning the film
to the sides and top of the window. DO
NOT ROLL THE WINDOW UP OR DOWN FOR 48-60 HOURS FOLLOWING APPLICATION TO ALLOW
THE MOISTURE TO EVAPORATE BELOW THE RUBBER GASKET. GENERAL
INFORMATION ·
If
bubbles occur at any time during installation, simply peel back the affected
area and re apply. Solarstat “EazyTint” can be removed, repositioned or re
applied at any given time. ·
If
you intend to Solarstat “EazyTint” seasonally, it is recommended that you
label and save the paper and packaging for storage. Simply release the static
bond by getting a fingernail under a corner of the film and peel from window. Re
roll the film in the appropriately marked paper and place it in the packaging
for storage. ·
Solarstat
“EazyTint” can be applied to most windows with ordinary household window
cleaner. If applying the film to plastic, it is recommended that you check with
the manufacturer before using any ammonia-based window cleaner. ·
After
installation, Solarstat “EazyTint” may appear slightly cloudy or tiny
pinhead bubbles may appear. This condition will improve as the moisture dries
between the film and the glass over the next 10-14 days.
|
|
